Analysis and interpretation of the dynamics in the reciprocating train according to the angular displacement of the crankshaft

Authors

DOI:

https://doi.org/10.37431/conectividad.v7i2.518

Keywords:

Reciprocating gearbox, Crankshaft, Mathematical modeling, Cylinder pressure, Mechanical forces

Abstract

The study analyzed the dynamics of the reciprocating assembly of a four-stroke gasoline engine using a mathematical model implemented in Microsoft Excel. Seventy-three crankshaft positions were evaluated—ranging from 0° to 720° in 10° increments—while accounting for cylinder pressure and the forces F, NE, KE, TE, and ZE. The resulting curves enabled an examination of load transmission among the piston, connecting rod, and crankshaft during the engine's intake, compression, expansion, and exhaust phases. The calculated peak pressure was 3,175.14 kPa at 370°. At this position, the model recorded maximum values ​​for F (180,17 kN), KE (180,18 kN), and ZE (177,28 kN). Peak values ​​for NE (1446,71 N) and TE (50,58 kN) occurred at 390°, demonstrating the influence of the mechanism's geometry on the angular distribution of forces. Pearson analysis revealed near-perfect associations between F and KE and between NE and TE, as well as strong correlations between F and ZE (r = 0.979) and between KE and ZE (r = 0.978). These associations stem, in part, from the equations linking the variables. A dimensional inconsistency was identified regarding the conversion of pressure and area into force; consequently, the reported absolute magnitudes require correction before physical interpretation. While the model describes trends and critical positions, its utility for assessing actual stresses requires a review of units, the incorporation of inertia and friction, and the validation of curves against experimental measurements of pressure and engine torque.

References

Almansoori, A. Q., Hajialimohammadi, A., Agha Mirsalim, S. M., & Mehrabivagha, M. (2022). Multi-objective Optimization and Sensitivity Analysis of the Parameters Affecting Sealing Performance of the Piston Rings Face through the Validated Model for the Four-stroke Bi-fuel Engine. Journal of Applied Fluid Mechanics, 15(5), 1345-1360. https://doi.org/10.47176/jafm.15.05.1073

Arunkumar, A., Sooriyamoorthy, A., Mishael, C., & Giri, A. (2022). A study on engine piston optimization by generative design approach. IOP Conference Series: Materials Science and Engineering, 1228(1), 1-12. https://doi.org/10.1088/1757-899x/1228/1/012014

Biet, C., & Krebs, S. (2022). Determination of Optimal Piston Trajectories for High Efficiency 4-Stroke Cycles by Using Predictive Combustion Modeling. Thermo, 2(4), 352-370. https://doi.org/10.3390/thermo2040024

Cakir, M. (2021). Experimental dynamic analysis of the piston assembly of a running single-cylinder diesel engine. Journal of Marine Engineering & Technology, 20(4), 235-242. https://doi.org/https://doi.org/10.1080/20464177.2019.1665257

Huping, A., & Shaowei, A. (2025). Kinematic and mechanical models of internal combustion engines and their characteristics. Proc.SPIE, 13965, 1050-1060. https://doi.org/10.1117/12.3092860

Mena Navarrete, L. A. (2011). Compilador de ejercicios de motores de combustión interna Diesel-Gasolina. Nueva Aurora.(págs. 48). Ecuador, Quito.

Mnati, H. M., Hammami, M., Ksentini, O., & Abbes, M. S. (2025). Study of Four-Stroke Engine Vibrations: Influence of Friction and Thermal Effects on Piston Speed, Displacement, and Acceleration. Journal of Techniques, 7(3), 70-81. https://doi.org/10.51173/jt.v7i3.2700

Nunes, A., & Brojo, F. (2022). Experimental Study of a Novel 4 Stroke Spark Ignition Geared-Hypocycloid Engine. ASME 2022 International Mechanical Engineering Congress and Exposition, 3. https://doi.org/10.1115/imece2022-95368

Ortolani, P., & Hall, A. (2022). Piston Concept, Design and Testing for Extreme High Efficiency Internal Combustion Engine Development. WCX SAE World Congress Experience, 1, 15. https://doi.org/10.4271/2022-01-0598

Perez, A., Valdes, A., Niño, G., Tamayo, C., Roman Flores, A., & Cuan-Urquizo, E. (2022). Mass Reduction and Enhanced Geometry of a 0.196 Liters Small IC Engine Piston Through Topology Optimization Simulation and Finite Element Analysis. Fuels & Lubricants Conference & Exhibition, 1. https://doi.org/10.4271/2022-01-1115

Pham, V. C., Kim, J. K., Lee, W.-J., Choe, S.-J., Le, V. V., & Choi, J.-H. (2022). Effects of Piston Bowl Geometry on Combustion and Emissions of a Four-Stroke Heavy-Duty Diesel Marine Engine. Applied Sciences, 12(24), 13012. https://doi.org/10.3390/app122413012

Pol, G. J., Jadhav, A. R., Shinde, J. G., Patil, Y., & Lokapure, R. B. (2023, march 31st). Design, Development and Analysis of the Electromagnetic Engine. National Conference on Emerging Trends in Engineering and Technology (NCETET-2023), Kolhapur, India. https://www.researchgate.net/publication/371350854_Design_Development_and_Analysis_of_the_Electromagnetic_Engine

Tretjakovas, J., & Juknelevičius, R. (2025). The Analysis of Bending Moment in Connecting Rod Caps for Internal Combustion Engines. En O. Prentkovskis, I. Yatskiv (Jackiva), P. Skačkauskas, M. Karpenko, & M. Stosiak (Eds.), Internactional Conference TRANSBALTICA XV: Transportation Science and Technology (pp. 649–658). Springer Nature Switzerland. https://doi.org/10.1007/978-3-031-85390-6_60

Ungureanu, L. M., Niculae, E., & Petrescu, F. I. T. (2022). Kinematic and dynamic study of a manipulator 1T6R. Independent Journal of Management & Production, 13(5), 1066-1092. https://doi.org/10.14807/ijmp.v13i5.1615

Published

2026-11-19
Crossmark

How to Cite

Passo Guamangate, R., Moncayo Condo, A. E., Moreta Tasinchano, K. J., Molina Morales, L. B., & Lisintuña Toapanta, E. P. (2026). Analysis and interpretation of the dynamics in the reciprocating train according to the angular displacement of the crankshaft. CONECTIVIDAD, 7(2), e518. https://doi.org/10.37431/conectividad.v7i2.518

Issue

Section

Scientific Articles and Review Articles

Categories

Most read articles by the same author(s)